Tin Sn · 50

A soft metal with a low melting point, which is why nearly every electrical joint in every device is held together with it.

Por que razão é importante?

Solder is about half of tin demand. It has been called the most electronics-exposed of all the base metals.

Where it is in the Earth

Where it is in the Earth

Tin is almost always found in a single ore mineral: cassiterite, which is tin dioxide. Cassiterite is chemically stable and physically hard, and it forms under specific conditions that do not occur widely. The mineral crystallises from hot, water-rich fluids that intrude into surrounding rock during the final stages of a granite body cooling deep in the crust. These fluids carry dissolved tin and deposit it in veins and fractured zones, a process geologists call hydrothermal mineralisation. The granite bodies associated with tin are of a particular chemical type — rich in silica, fluorine and boron — and the tin tends to concentrate at or near the boundary between the granite and the older rocks it has intruded.

Because cassiterite is so physically resilient, it survives erosion long after the original host rock has been broken down by weathering. The heavy mineral grains wash into rivers and accumulate on stream beds and in coastal sediments, forming deposits called placers or alluvials. Much of the world's historical tin production came from exactly this kind of deposit. The great tin belts of Southeast Asia — running through Myanmar, Thailand, Malaysia and Indonesia — are classic examples of alluvial tin districts, where erosion of older granite-hosted veins fed metal into river systems over millions of years. In contrast, the tin districts of Bolivia and parts of Brazil and the Democratic Republic of Congo are primary hard-rock deposits where the original veins have not been fully eroded away.

The concentration of tin in ordinary crustal rocks is very low, which means a deposit needs to be substantially enriched above background levels before mining makes any sense. The geological conditions required — the right granite chemistry, the right depth, the right fluid circulation — do not come together in many places on Earth, which explains why meaningful tin deposits are found in a relatively small number of countries and why the metal has historically commanded a price far above the commonest industrial metals.

Getting it out

Getting it out

How tin is extracted depends almost entirely on the type of deposit. Alluvial deposits, where cassiterite grains sit in loose sand and gravel, are worked by methods closer to large-scale hydraulic excavation than to conventional hard-rock mining. Dredges — floating machines that scoop up the sediment from riverbeds or shallow coastal areas — have long been the defining image of Southeast Asian tin production, particularly in Indonesia and Malaysia. The gravel is lifted aboard, the cassiterite is separated by its high density using gravity, and the tailings are discharged back into the water. The ore grades in alluvial deposits are typically measured in grams of tin per cubic metre of material processed rather than as a percentage by weight, because the tin is thinly dispersed through enormous volumes of sediment.

Hard-rock deposits are a different matter. Here, the cassiterite sits in veins or disseminated through rock, and the ore must be drilled, blasted and hauled before any separation can begin. Deposits near the surface are mined by open pit; deeper ones require underground development with shafts or declines. Bolivia's tin mines are famously high-altitude underground operations working narrow, high-grade veins under physically demanding conditions. In the Democratic Republic of Congo, much production comes from artisanal and small-scale miners using manual methods — picks, shovels and hand-operated sluices — in difficult terrain with minimal infrastructure.

The grade of a tin deposit — the concentration of metal in the ore — matters enormously to the economics. A higher-grade deposit can sustain expensive underground methods; a lower-grade deposit may only be viable as an alluvial or open-pit operation where the volume of material processed is very large and the mining cost per tonne of ore is low. Either way, for every tonne of refined tin produced, a much larger mass of waste rock or tailings must be moved and managed, and the ratio of waste to product is a central constraint on both cost and environmental impact.

What pulls on it

What pulls on it

The dominant use of refined tin is as solder — the metal alloy that physically connects components to printed circuit boards and joins wires in almost every electronic device made. When solder is applied in liquid form and allowed to solidify, it creates an electrical and mechanical joint. Tin's low melting point makes it practical for this purpose, because the temperatures needed to reflow solder are low enough not to damage delicate components. No other widely available metal combines the melting point, electrical conductivity, wettability and non-toxicity that solder requires, which is why the connection between tin demand and the electronics industry is so direct.

A second major use is tinplate — thin sheet steel coated with a layer of tin to prevent corrosion. Tinplate is the material of food cans and a wide range of packaging. This use is mature and in long-term modest decline in many high-income markets as competing packaging materials take share, though food-can production remains very large in absolute terms globally. Tin is also consumed as a chemical intermediate, particularly in organotin compounds used in PVC stabilisers and agricultural applications, and as a component of specialty alloys including bronze and bearing metals.

The direction of demand is largely set by electronics. The ongoing spread of semiconductor content into vehicles, the construction of data centres, the expansion of solar power installations — all of which require soldered connections — tends to support tin consumption. Each solar panel contains solder-coated copper ribbon connecting cells, and the quantity of solder involved across a large installation is not trivial. A sharp slowdown in electronics manufacturing would weaken tin demand significantly, while a prolonged acceleration in the deployment of solar, electric vehicles or server infrastructure would pull in the other direction. The intensity of tin use per device is not fixed: as electronics are miniaturised, less solder is used per joint, but the number of joints per device has also grown, and the two effects have broadly offset each other over time.